USING SYNTHESISED ORGANIC COMPOUNDS AS ENVIRONMENTALLY FRIENDLY RETARDANTS FOR ORNAMENTAL PLANTS
The pre-sowing treatment of scarlet sage (Salvia splendens Ker Gawl.) seeds with 4-methyl-2-piperidin1-yl-pyrimidine-5-carboxylic acid at concentrations of 0.01, 0.05, and 0.1% proved to have an obvious inhibiting effect. Prior to sowing, the seeds of Salvia splendens were soaked in a water suspension of 4-methyl-2-piperidin-1-yl-pyrimidine-5-carboxylic acid and 4-methyl-2-morpholin-4-pyrimidine-5-carboxylic acid with concentrations of 0.01%, 0.05%, and 0.1% for 18 hours. On the 42nd day of the experiment, the seedlings, having been preliminarily hardened for 12 days, were removed from the greenhouse and planted on the field. The pre-sowing treatment of Salvia splendens seeds with 4-methyl-2-morpholin-4-pyrimidine-5-carboxylic acid proved to have the inhibiting effect at concentrations of 0.01 and 0.05%. The height of the seedlings decreased by 13.3-43.7%. It was revealed that 4-methyl-2-piperidin-1-yl-pyrimidine-5-carboxylic acid at concentrations of 0.01, 0.05, and 0.1% decreased the growth of the seedlings by 30.4-43.7%, and 4-methyl-2-morpholin-4-pyrimidine-5-carboxylic acid at concentrations of 0.01 and 0.05% decreased the growth of the seedlings by13.3-22.2%. By contrast, the effect of pyrimidinecarboxylic acids on seed germination and plant height of another annual flower – spreading marigold (Tagetes patula L.) was stimulating. It was investigated some different concentrations from 0.01 to 0.05 %. The same concentrations of identical compounds were tested, but effects from them were opposite for Tagetes patula, and Salvia splendens seedlings. Сonsequently, the species-specific effect of pyrimidinecarboxylic acids on seed germination and plant height for ornamental grasses takes place. Therefore,4-methyl-2-piperidin-1-yl-pyrimidine-5-carboxylic acid and 4-methyl-2-morpholin4-pyrimidine-5-carboxylic acid are recommended as growth retardants for Salvia splendens.
Read ArticleMANAGEMENT MODEL FOR CONSTRUCTION WASTE PRODUCED IN THE CITY OF RIO DE JANEIRO
Background: A new management model for construction and demolition waste (CDW) was proposed for the city of Rio de Janeiro, hence waste the city planning area estimated generation; the results were compared with the data published by COMLURB and SNIS through the statistics tests was proved that CDW had been dispersed, which support the hypothesis that the current model cause dispersion of the rubble. Aim: This study proposes a new management model for CDW to the city, according to regions where occur the higher production of rubble. Methods: The estimation of rubble was obtained through the issued licenses from 2006 to 2020 published by SMPU. The quantification of rubble in the city was carried out by adopting the generation indicator from licensed construction activities. The amount of CDW published by COMLURB and SNIS was compared through statistics tests ANOVA and T-Test, the second period from 2006 to 2020 and 2011 to 2020. To measure the area to implant a CDW recycling plant, criteria from production capacity were used. Results: ANOVA test to data from 2006 to 2020 and 2011 to 2020, according to a confidence interval of 95%, found the P value 0.589 and 0.022, respectively, it was verified that the significant difference is between data from COMLURB and Estimated. The T-test was applied from the same period in data from SNIS and estimated the P values 0.399 and 0.014. Discussion: The data from Estimating between 2006 and 2020 showed the best representation. The Área de Planejamento – AP (Planning Area) 4 was where 50.70% of the total rubble, after the AP 3 with 17.66%, the AP 5 was estimated at 16.59%, last of all, AP 2 and AP 1 were calculated the generation of 8.28% and 6.77%, respectively. Therefore, sizing the CDW recycling producing 361,99.00 tons per year demands an area of 32,397.50 m². Conclusions: It was concluded that the receipt of CDW in transfer stations managed by COMLURB is not allowed; therefore, the need to create a construction waste recycling plant was presented, to this end, it is necessary to have an available area of approximately 32,397.50 m².
Read ArticleCLINICAL AND LABORATORY TESTING OF A NEW MODIFICATION OF TWO-LAYER "SILEP" DENTURES USED IN PROSTHETIC DENTISTRY
Dentistry is a part of medicine, where various polymer materials were used for the first time. Many factors forced researchers to find more stable, versatile, and hygienic materials for the manufacture of dental products. It is important to note that the search for the ideal polymer dental material is still ongoing. This is because modern polymers, in some cases, do not meet the specified requirements for chemical, physical, strength, and elasticproperties. Based on the data on the method of creating and using silicone material for the base of the removable prosthesis "Gossil", an improved silicone material for two-layer dentures "Silep" was developed, as well as a special primer for better connection of the lining with the rigid acrylic base of the prosthesis. To evaluate the most suitable compound, materials were tested for several parameters, such as tensile strength, elongation, and shore hardness. In addition to selecting a suitable material for modification, the selection and testing of an adhesive that allows the chemical bonding of the acrylate surface to the siloxane surface were carried out.
Read Article