THE INFLUENCE OF CLIMATIC FACTORS ON THE CHANGE IN THE ELASTIC-STRENGTH INDICATORS OF EPOXY POLYMERS BINDERS USED IN LIQUID THERMAL INSULATION COATINGS
Introduction: Thermal insulating coatings are increasingly being introduced into construction practice for internal and external finishing enclosing structures and pipelines. Thermal insulation coatings are usually made based on polymer binder and mineral fillers. The durability and stability of the properties of heat-insulating materials depend on the type of binder. As a rule, polymers are used as a binder: epoxy resin; silicone rubber; urea-formaldehyde resins; aqueous dispersed polymers - styrene-butadiene, polyvinyl acetate, and acrylate (acrylic and styrene-acrylic). The quality indicator of binders can be assessed by the influence of the seasonality of climatic impact, and as a result, the best elastic strength characteristics of binders can be established after one month to a year of field tests. Aim: To determine the influence of climatic factors on the change in the elastic-strength indicators of epoxy polymers binders used in liquid thermal insulation coatings. Methods: A tensile testing machine of the AGS-X series with the TRAPEZIUM X software was used for mechanical tests. The tests were carried out in accordance with GOST 11262-2017 (ISO 527-2: 2012) "Plastics. Tensile test method". Results and Discussion: The paper discusses the results of experimental studies of the compositions of polymer binders and their resistance to various climatic factors, which will later be used as a polymer binder for thermal insulation coatings based on fine mineral granular systems. Conclusions: When analyzing the changes in the characteristics of polymer samples after exposure to climatic factors, it was found that compositions based on Etal-247 epoxy resin, cured with amine hardeners Etal-1440N, Etal-1460, Etal-1472, and Etal-45M, demonstrate the best elastic strength characteristics after one year of full-scale tests. The high stability of the indicators under consideration allows us to conclude that the use of Etal-247 resin as a base leads to creating of the most climate-resistant epoxy coatings.
Read ArticlePRODUCTION OF BIOPLASTIC FROM POTATO STARCH
Due to their diverse properties, plastic materials are used in numerous sectors. It is possible to produce different articles and plastic objects with reduced costs, being more accessible to the population. Conventional plastics are obtained from petroleum-derived raw materials, a non-renewable resource in which their extraction and refining process cause major environmental impacts. The production of plastic reaches a level of approximately one hundred and forty million tons per year, and the disposal of these materials is increasing, generating a high rate of waste and leading to an increase of pollution since the decomposition of these materials lasts about five hundred years old. Conventional plastics can be replaced by bioplastics, a material obtained from renewable raw materials such as potatoes, cassava, maize, and which, when disposed of under favorable conditions, decomposes faster, as during its degradation process at least one step occurs. Through the metabolism of organisms present in the environment. Starch has been widely used in the production of biodegradable packaging, so the objective of this work was to produce a biodegradable bioplastic from the potato starch. Potato starch, glycerin, hydrogen peroxide, distilled water, and commercial agar were used to produce the bioplastic. Bench-scale bioplastics had good organoleptic characteristics, similar in appearance to a conventional plastic obtained from petroleum. The thickness, moisture content, and solubility of the bioplastics were analyzed, as well as their fruit preservation capacity. The samples produced were rigid and with good resistance.
Read ArticleE-SELECTIN AS A BIOMARKER IN FEMALE PATIENTS WITH Β-THALASSEMIA IN AL- NAJAF PROVENCE, IRAQ
E-selectin, as identified (CD62E), is expressed on endothelial cells after stimulation with inflammation cytokines. β-Thalassemia diseases (βT) and early diagnosis are of utmost significance in the entire world population. This study was performed in the Thalassemia Center of the Al-Zahraa Educational Hospital in Al-Najaf Province, Iraq, on sixty-nine with β-thalassemia (54 βT major and 15 βT Intermedia) aged 8-40 years who transfused blood. Compared to 20 healthy volunteers as a control group. In both βT patients and healthy groups were assessed serum E-selectin levels. It was investigated the relationship with RBC, Hb, PCV, WBC, PLT, BMI, splenic status, iron, and ferritin levels. The results revealed a significant (P<0.05) decreased values of HB, RBC, P.C.V, and BMI. In contrast, values of WBC, PLT, Iron, and Ferritin were significantly increased in βT patients as compared to the healthy control groups. A significant (P<0.05) increase in serum E- Selectin level in βT patients (20.55±0.47) ng/ml to compare with the healthy group (9.16±0.50) ng/ml. Furthermore, it was a significant decrease in groups of βT major (19.87±0.42) ng/ml more than in βT intermedia (23±1.42) ng/ml. E-Selectin revealed a significant increase (P<0.05) in progress age and associated with splenectomies and underweight groups compared to splenectomies and the normal weight groups, respectively. Also, E-Selectin levels significantly positively correlated with WBC, PLT value, iron, and Ferritin levels. However, it was no significant with RBC, PCV, Hb. As a conclusion from this study, E- Selectin is an important biomarker in β-thalassemia patients can be identified as the complications associated with iron overload, inflammatory process, and endothelial dysfunction in βT disease.
Read Article