SOUTHERN JOURNAL OF SCIENCES

Background: MQ-series gas sensors belong to the metal oxide semiconductor (MOS) family of sensors that can sense the presence of many gases. These sensors find their application in gas alarm systems as key components. While necessary sensor circuit output voltage value for alarm point in a stand-alone gas alarm system is desirable, but what exact combination of the sensor circuit parameters is required? Hitherto, the determination of these circuit parameters has not been given much attention in the research community. Aim: the purpose of this work is to explore a structured graphical approach of determination of MQ series gas sensor circuit parameters for a stand-alone gas alarm system that yields desired sensor circuit output voltage value for the alarm point; the main objective of the study was to develop mathematical model equations that relate the: (i) sensor resistance (RS) with the gas concentration (x) and the sensor resistance at standard calibration concentration of the sensor base gas in the clean air (Ro) and (ii) sensor circuit output voltage (VRL), load resistance (RL) and sensor resistance (RS). It is expected from the model equations developed that graphical correlations of the sensor circuits parameters will be generated. Using these graphs for a particular case of an MQ-4 gas sensor under the influence of LPG, the parameters that yield desired sensor circuit output voltage of 2V for 1000 ppm of LPG alarm point will be determined. Methods: Model equations were developed for the sensor dynamics, and based on these model equations, graphs for the determination of required sensor parameters were plotted for a case of MQ-4 gas sensor response to LPG. Results and Discussion: The results yielded optimal values for R_O,R_S and R_L of 20 kΩ, 30 kΩ and 20 kΩ respectively, for alarm settings of 1000 ppm and a desired sensor circuit output voltage of 2 V. Based on determined parameters, the calibration equation for determination of best concentration value for a given value of emulated LPG concentration was developed. Using the method proposed in this study makes the process of determining the MQ-series gas sensor circuit parameters less cumbersome as their value can easily be obtained from the resulting graphs. Conclusions: a structured graphical approach for determination of MQ-series gas sensor circuit parameters for alarm points in a stand-alone gas alarm system showed that using MQ-4 gas sensor and LPG as the target gas, and for a sensor circuit output voltage of 2 V for alarm point at 1000 ppm of LPG, the corresponding value of R_O, R_S and R_L obtained were 20 kΩ, 30 kΩ, and 20 kΩ respectively. Hence, a structured graphical approach is suitable for determining MQ series gas sensor circuit parameters for a stand-alone gas alarm system under the influence of its associated gases.

Background: Despite innovations in orthopedic dentistry, the manufacture of removable dentures belongs to the most popular orthopedic care category. Removable dentures are combined stimuli that affect the mucous membrane and neuro-receptor apparatus. Acrylic plastic prostheses, widely used in prosthetic dentistry, have a negative side mechanical, chemical-toxic, sensitizing, and thermal insulating effect on oral tissue and prosthetic impression area. This is often complicated by a violation of the biocenosis of the oral cavity, the growth of pathogenic microflora that releases toxins, especially an increase in the number of yeast colonies that irritate the oral mucosa and prosthetic stomatitis. According to the WHO, one-fifth of the world s population suffers or has suffered various candidiasis forms at least once. The worldwide increase in the incidence of the disease is primarily related to the fact that this infection is opportunistic, more than half of the world s population is a carrier of fungi of this kind, i.e., in most cases, it is an endogenous infection, which makes candidiasis different from other opportunistic mycoses. Aims: The purpose of this study was to study the prevalence of candidiasis in patients using removable dentures and to evaluate the effectiveness and prevention of candidiasis treatment. Methods: 100 patients with oral candidiasis of various age groups from 45 to 65 years were observed. Of these, 60 patients with removable plate prostheses; 40 patients with partially removable prostheses. Results and Discussion: Chronic forms of candidiasis were diagnosed in 40 patients and with exacerbation of chronic forms of candidiasis-60 people. The number of untreated carious cavities and poor hygienic condition of the oral cavity directly affects the severity of candidiasis. Acute forms of candidiasis were observed mainly in patients with high DMF and PMA indices. The severity of candidiasis depends on the degree and duration of wearing dentures and hygienic conditions - the most severe forms of invasive candidiasis were observed in the presence of removable plate prostheses, the complete absence of teeth, and the use of a prosthesis for more than 10-15 years. A combined lesion of the oral mucosa and the red border of the lips was observed mainly in patients older than 60 years. Conclusions: The presence of candidiasis in the oral cavity in patients with removable plate prostheses leads to a statistically significant change in the indicators of local immunity of the oral cavity: an increase in the concentration of serum IgG and IgA and the values of the coefficient of the balance of local immunity factors.

Sugar beet is a crop able to resist high levels of soil salinity after emergence and establishment. Considering the significant difference in the effect of nitrogen forms on sugar beet performance under normal conditions, the form of nitrogen may affect the performance of sugar beet plants under abiotic stress, particularly salinity. Additionally, exploring the most appropriate type of nitrogen for sugar beet could mean optimizing sucrose content. Therefore, here using two lines, sugar beet was grown in pots (filled with 4 kg soil), salt-resistance (line 7233- p.29 x Mst), and salt-sensitive (line 3929-21939), the effect of two different forms of nitrate in the form of calcium nitrate (1 g per pot) and ammonium in the form of ammonium sulfate (1 g per pot) under normal and salt stress condition (40 Millimoles per liter sodium chloride) were evaluated. The result revealed the positive influence of nitrate over ammonium by indicating higher dry weight in both sensitive line: 19.2 and 13.6 g, and tolerance line: 20.4 and 13.6 g, respectively alone and in combination with salinity stress. Similarly, root yield levels positively influenced by nitrate treatment either alone or under salinity stress (sensitive line: 194.5 and 243.2 g and tolerance line: 207 and 249.5 g). The outcomes additionally showed the accumulation of proline aerial parts in both lines, and however, the proline accumulation of sensitive line was higher (3.9 mg/g dry weight). Moreover, induction of proline aggregation was considerably higher in nitrate nitrogen-treated sensitive line (9.3 mg/g dry weight). The absence of significant difference was obseved between nitrogen treatments in terms of extractable sucrose and root molasses sugar. Also, the root impurities increased in those treated with nitrate-nitrogen and salinity. It can be concluded that nitrate-nitrogen has improved the performance of both sugar beet lines against salinity stress, and its practical application is adviseable.