COMPARISON OF TWO STAINING METHODS FOR ANODIZING IN ALLOY 6063 ALUMINUM PROFILES
Background: Aluminum stands out for being a light, corrosion-resistant, and recyclable metal, achieving wide coverage in the market. When incorporated into alloying elements, it is possible to acquire other desirable characteristics. Alloy 6063, intended for architectural purposes, has aesthetic, structural, and strength functions. Anodized finishing is performed through an electrolytic process, ensuring a more resistant aluminum oxide film than that formed naturally. For decorative purposes, the anodic film coloration can be performed by several methodologies, in this case, for the coloration by organic adsorption, with the use of aniline, and the electrolytic coloration, composed of tin sulfate salts, both for obtaining the black color. Aim: Compare of two different staining methods on the surface of anodized profiles of aluminum alloy 6063. Methods: Profile samples were collected and tests were carried out to measure the thickness of the anodic layer, immersion tests with 3,5 percent sodium chloride, for 1000 hours, and neutral saline mist, for 600 hours. Results and Discussion: Both methodologies proved to be resistant to immersion tests with sodium chloride, as well as with neutral saline mist, and these tests are quite aggressive and provide corrosion of the material when not well treated. Corrosion points were only seen at the intersections performed, and in the rest of thearea, no points were detected. Conclusions: The result of both methodologies was positive, considering tht there was no corrosion in the tested samples, except in the intersections performed, as well as the maintenance of the color in both tested methodologies, which was not expected in the literature. For future work, it is suggested to deepen the study to perform electrochemical impedance spectroscopy tests for exaluate the strength of the anodic film and perform anodizing with the same parameters, however, with different anilines to analyze their behavior.
Read ArticleEXPERIMENTAL SUBSTANTIATION OF MANURE FRACTIONATION ON PIG FARMS USING A SPIRAL-SCREW MECHANISM
The main vector of mechanization and automation of livestock farming at the present stage of technological development of producers is the improvement of resource-saving technologies and technical devices that enables agricultural producers to produce relatively expensive and high-quality equipment to improve conditions for the animals. This article was considered a method for effective fractionation of manure on pig farms to further obtain humus for soil fertilization. The optimal conditions for the performance of the presented gadget were identified, namely: the time spent by the manure mass in the rotor is 0.1, with a separation factor of 170 to 180, the partition for the filter is made of metal sheet with holes whose diameter varies from 0.8 to 1.5 mm and a thickness of no more than 1 mm. The device presented in the manuscript has several advantages in the form of automation, low energy consumption and cost, novelty, and high efficiency.
Read ArticleDENSE CLUSTERS OF RAW SEWAGE LOCATIONS ON MINNA NEIGHBOURHOOD GIS MAPS ARE POINTERS TO VERITABLE URBAN DECAY AND MOSQUITO-BREEDING GROUNDS
Background: The lack of comprehensive baseline data on raw sewage pollution in Minna, Nigeria's Niger State capital, represents a significant gap in public health information. This deficiency necessitates a systematic study to establish a database documenting sewage pollution patterns in Minna's urban environment. Aim: To employ georeferencing tools and descriptive observations for identifying and mapping potential mosquito breeding sites related to sewage discharge within Minna's built-up areas and to develop an interactive Geographic Information System (GIS) map as an environmental audit tool for public health officials. Methods: The study area was divided into five sectors: Greater Bosso, Minna Central, Greater Maitumbi, Tunga, and Greater Chanchaga. Following initial site familiarization and GIS equipment testing, systematic surveys were conducted. Field teams documented locations of household sewage discharge points, collecting geographic coordinates, temporal data (date, time, weather conditions), and site characteristics. Each identified location was photographed and recorded in standardized data sheets, including household information where available. Results: Using ArcGIS®10.8 software, comprehensive sewage pollution layers were created for each sector by integrating collected field data with Minna's township built-up and settlement shapefiles. The mapping revealed distinct pollution patterns and clusters across different neighborhoods. Discussion: Analysis of the spatial distribution showed a clear correlation between socioeconomic status and sewage management practices, with higher concentrations of improper sewage discharge in low-income areas. Conclusions: This database serves as a valuable resource for public health interventions targeting mosquito breeding grounds. Regular monitoring through periodic sewage pollution audits and expanded geographical coverage is recommended for improved urban health management.
Read Article