ADSORPTION STUDIES OF ZINC, COPPER, AND LEAD IONS FROM PHARMACEUTICAL WASTEWATER ONTO SILVER-MODIFIED CLAY ADSORBENT
Background: Industrial wastewater contains pollutants that are detrimental to human health in varied proportions. Among the pollutants are heavy metals, including Zn2+, Pb2+, and Cu2+ found in a characterized pharmaceutical wastewater. Several techniques have been proposed for the heavy metal sequester. However, they are with attendant challenges. The adsorption techniques using clay-metal oxide modified adsorbent/composite such as silver-clay adsorbent is considered suitable for an effective sequestering process. Aims: To develop and characterize Ag/clay adsorbent for pharmaceutical wastewater treatment. Methods: The Ag nanoparticles were synthesized using Parkia biglobossa aqueous leaves extract in an optimization study. The raw clay was beneficiated and doped with silver nanoparticles via the wet impregnation method. The silver-clay adsorbent was characterized using FTIR, XRD, SEM, and EDS characterization tools. The developed adsorbent was used for the batch adsorption process of the heavy metal ion removal from the wastewater. Results and Discussion: The phytochemical analysis and FTIR results of the P. biglobosa showed that the leaf contains phenol, tannin, and flavonoids which acts as reducing, capping, and stabilizing agent required for synthesizing the silver nanoparticles. The prepared silver nanoparticles modified clay adsorbent Ag/clay, have evenly distributed stacks of pseudo-hexagonal plates, are rich in silica, possess silver nanoparticles in the frameworks, and contain functional groups suitable for binding heavy metals. The adsorptions of Zn2+, Pb2+, and Cu2+ from pharmaceutical wastewater onto the silver-modified clay were studied as a function of adsorbent dosage and contact time. The percentage removal results obtained showed that the adsorbent had up to 99.96%, 99.5%, and 99.44% removal efficiency for Zn2+, Pb2+, and Cu2+, respectively, which are better compared with previous studies. The adsorption process was feasible, spontaneous, and exothermic, with Langmuir and Pseudo-second-order models as best fits for the process. Conclusions: The adsorption of selected heavy metal ions onto the green synthesized silver-modified clay adsorbent (Ag/clay) was feasible, spontaneous, and exothermic in the order Zn2+>Pb2+>Cu2+ with Langmuir and Pseudo-second-order model best fitted for the process. These show that the synthesized silver oxide nanoparticles supported on local clay can be used as a potentially low-cost adsorbent to remove heavy metal ions from industrial wastewater.
Read ArticleCLINICAL AND LABORATORY TESTING OF A NEW MODIFICATION OF TWO-LAYER "SILEP" DENTURES USED IN PROSTHETIC DENTISTRY
Dentistry is a part of medicine, where various polymer materials were used for the first time. Many factors forced researchers to find more stable, versatile, and hygienic materials for the manufacture of dental products. It is important to note that the search for the ideal polymer dental material is still ongoing. This is because modern polymers, in some cases, do not meet the specified requirements for chemical, physical, strength, and elasticproperties. Based on the data on the method of creating and using silicone material for the base of the removable prosthesis "Gossil", an improved silicone material for two-layer dentures "Silep" was developed, as well as a special primer for better connection of the lining with the rigid acrylic base of the prosthesis. To evaluate the most suitable compound, materials were tested for several parameters, such as tensile strength, elongation, and shore hardness. In addition to selecting a suitable material for modification, the selection and testing of an adhesive that allows the chemical bonding of the acrylate surface to the siloxane surface were carried out.
Read ArticleINTERACTIVE 3D RECONSTRUCTION AND DLT CAMERA CALIBRATION: A MANUAL REGISTRATION APPROACH
Background: This paper presents a straightforward and intuitive method for interactive 3D reconstruction and Direct Linear Transformation (DLT) camera calibration using a single image of a structured scene with known object dimensions. The method relies on manual registration of pairs of points on both the image and the terrain, allowing for precise alignment and calibration. Aim: By utilizing this method, users can easily reconstruct 3D scenes and calibrate cameras without the need for complex algorithms or extensive computational resources. Our approach offers a user-friendly solution for 3D reconstruction and camera calibration, making it accessible to a wider audience and applicable in a range of fields such as computer vision, augmented reality, and virtual reality. Methods: This work primarily focuses on the determination of the projection matrix, which plays a crucial role in mapping 3D points onto a 2D image plane. The projection matrix encapsulates both the intrinsic parameters of the camera (such as focal length and optical center) and the extrinsic parameters (such as camera position and orientation in the world coordinate system). By accurately determining the projection matrix, we can effectively project 3D points onto the 2D image plane, enabling tasks like 3D reconstruction, camera localization, and augmented reality applications. Results: We present experimental results obtained from testing the method on an image of a known object, demonstrating its effectiveness and accuracy in producing realistic 3D reconstructions. Discussion: The method's reliance on manual registration of point pairs allows for precise alignment and calibration without the need for complex algorithms or extensive computational resources. This user-friendly approach makes 3D reconstruction and camera calibration accessible to a wider audience and applicable in various fields. Conclusions: Overall, our approach offers a practical and accessible solution for 3D reconstruction and camera calibration, expanding the potential applications in computer vision, augmented reality, and virtual reality.
Read Article