PRODUCTION OF BIOPLASTIC FROM POTATO STARCH
Due to their diverse properties, plastic materials are used in numerous sectors. It is possible to produce different articles and plastic objects with reduced costs, being more accessible to the population. Conventional plastics are obtained from petroleum-derived raw materials, a non-renewable resource in which their extraction and refining process cause major environmental impacts. The production of plastic reaches a level of approximately one hundred and forty million tons per year, and the disposal of these materials is increasing, generating a high rate of waste and leading to an increase of pollution since the decomposition of these materials lasts about five hundred years old. Conventional plastics can be replaced by bioplastics, a material obtained from renewable raw materials such as potatoes, cassava, maize, and which, when disposed of under favorable conditions, decomposes faster, as during its degradation process at least one step occurs. Through the metabolism of organisms present in the environment. Starch has been widely used in the production of biodegradable packaging, so the objective of this work was to produce a biodegradable bioplastic from the potato starch. Potato starch, glycerin, hydrogen peroxide, distilled water, and commercial agar were used to produce the bioplastic. Bench-scale bioplastics had good organoleptic characteristics, similar in appearance to a conventional plastic obtained from petroleum. The thickness, moisture content, and solubility of the bioplastics were analyzed, as well as their fruit preservation capacity. The samples produced were rigid and with good resistance.
Read ArticleMETHODOLOGY FOR DETERMINATION OF DEGREE OF NODULARITY IN A DUCTILE CAST IRON GGG 40 BY ULTRASONIC VELOCITY TEST
Cast iron alloys combine many elements such as carbon, iron, silicon, magnesium and can be usually classified according to their microstructure in ductile, gray, compacted, white, and malleable. Each one has particularities in terms of properties and applications. Hence, this study aims to evaluate the degree of nodularity (%) in a ductile cast iron alloy GGG 40. In this context, a methodology to investigate the degree of nodularity wasproposed. The ultrasonic method was used to determine the amount of ductile graphite as well as for parts release and thus facilitated the industrial operational execution. The effect of ultrasonic sound was investigated in sixtyseven ductile cast irons, and these analyses were further compared to the level of nodularity observed by metallography. Finally, based on the findings, the cast iron quality was guaranteed, leading to time savings, avoiding the microstructural examination, and thus promoting cost reductions.
Read ArticleEXTRACTION AND CHARACTERIZATION OF CURCUMIN FROM TURMERIC RHIZOMES GROWN IN MÉRIDA, VENEZUELA
The extraction of naturally occurring compounds is one of the fastest-growing industries because of its benefits against its synthetic analogs. Environmental protection must require the use of natural products instead of chemicals to minimize pollution. Thus, this investigation studies the use of some natural product, as curcumin, as naturally occurring acid‐base indicators. Curcumin can be used as acid-base indicators since it was found that it possesses pH-dependent solubility. Curcumin, the major active component of turmeric, Curcuma longa (Zingiberaceae), is used as a spice in curry and as a coloring agent in yellow mustards, cosmetics, pharmaceuticals, and hair dyes. In this research, the main compound colored rhizome of turmeric (Curcuma longa) cultivated in Mérida, Venezuela, is extracted: Curcumin (C21H20O6) (1E,6E)-1,7-bis(4-hydroxy-3-methoxyphenyl)-1,6-heptadiene-3,5-dione, in a yield of 3.42% after 8 hours of extraction using soxhlet extractor system with organic solvents (hexane and ethanol). The thin-layer chromatography and column performed separation and purification using a mobile phase, a mixture of chloroform-hexane 3:2. The dye was characterized by spectroscopic analysis of visible ultraviolet (UV-Vis) and infrared (IR), in addition to his studio in steering sensitivity as an acid-base indicator. This dye is useful as an acid-base indicator in strong acid-strong base volumes and did not require large amounts of it as it has high sensitivity. The results indicate that curcumin as an acid-base indicator allows the development of new standards in different chemistry fields that require this type of analysis.
Read Article