BUNCH NUMBER AND ANTIOXIDANT ACTIVITY IN ‘SAHEBI’ AND ‘HALAGHO’ GRAPES AFFECTED BY PRUNING INTENSITY AND CANE LENGTH
Pruning methods can primarily affect grape production at various levels. Of the commonly affected features by pruning, the number of bunches has known to have a significant effect on the relation between the functions of assimilate sources and sinks. Further, fruitfulness can significantly be negatively influenced by shading. In this study, we aim to study the impact of 4, 6 and 8 buds per cane with pruning intensity as light, moderate and severely pruned and their interaction in the course two consecutive years, 2017 and 2018 in ‘Sahebi’ and ‘Halagho’ (both seeded red table grape cultivars). In 2018, lightly pruned ‘Halagho’ and having 8 buds per cane increased number of bunches by 54.00, which had the highest value. Results showed that there is apical buds bear more fruit by comparison to the buds with vegetative nature, 1 to 4 first buds. Based upon the outcomes of this study, it could be concluded that due to the stresses imposed by the pruning of the vines, therefore, the chemical compounds increases in order alleviate the negative aftermaths . In 2018, whole berry antioxidant activity in both cultivars was significantly lessened, and this decline was higher in ‘Saahebi’. The number of bunches was increased by increasing cane length or bud load/cane. Overall, the pruning program has an impactful role in bunch number as well as antioxidant activity and in the long-run on accumulated reserves, which makes choosing and applying a specific pruning method undeniably important. Thus, emphasize the importance of further research in this field.
Read ArticleCOMPARISON OF TWO STAINING METHODS FOR ANODIZING IN ALLOY 6063 ALUMINUM PROFILES
Background: Aluminum stands out for being a light, corrosion-resistant, and recyclable metal, achieving wide coverage in the market. When incorporated into alloying elements, it is possible to acquire other desirable characteristics. Alloy 6063, intended for architectural purposes, has aesthetic, structural, and strength functions. Anodized finishing is performed through an electrolytic process, ensuring a more resistant aluminum oxide film than that formed naturally. For decorative purposes, the anodic film coloration can be performed by several methodologies, in this case, for the coloration by organic adsorption, with the use of aniline, and the electrolytic coloration, composed of tin sulfate salts, both for obtaining the black color. Aim: Compare of two different staining methods on the surface of anodized profiles of aluminum alloy 6063. Methods: Profile samples were collected and tests were carried out to measure the thickness of the anodic layer, immersion tests with 3,5 percent sodium chloride, for 1000 hours, and neutral saline mist, for 600 hours. Results and Discussion: Both methodologies proved to be resistant to immersion tests with sodium chloride, as well as with neutral saline mist, and these tests are quite aggressive and provide corrosion of the material when not well treated. Corrosion points were only seen at the intersections performed, and in the rest of thearea, no points were detected. Conclusions: The result of both methodologies was positive, considering tht there was no corrosion in the tested samples, except in the intersections performed, as well as the maintenance of the color in both tested methodologies, which was not expected in the literature. For future work, it is suggested to deepen the study to perform electrochemical impedance spectroscopy tests for exaluate the strength of the anodic film and perform anodizing with the same parameters, however, with different anilines to analyze their behavior.
Read ArticleSYSTEM OF ADSORPTION OF CO2 IN COALBED
Carbon capture and storage (CCS) has been observed as an alternative measure to mitigate emissions from greenhouse gases. CCS systems separate CO2 during the process of converting fuel and transport to the facilities where they are stored, e.g., under geological formation conditions. Capture and sequestration technologies are now widely used in different industries. CO2 capture is currently a costly and energy-consumingtechnology. The costs obviously depend on the size of the plant and the type of fuel used. Generally, capture systems are categorized into three categories: pre-combustion, post-combustion, and oxy-fuel combustion. The saline aquifer, depleted oil, and gas fields are large-capacity storage sinks. The coalbeds also provide as a substitute to geological storage. One of the main advantages of coal storage is renewable methane fuel and coaldesulfurization. The studied coal reserves are located in Candiota, State of Rio Grande do Sul, Brazil. These are the largest coal deposits in the country, with a reserve of 1 billion tons. This work will represent a study on CO2 storage in Candiota coalbed system. The use of a synthetic CO2 cylinder with a flow of 0.2 L/min varies the time of contact with the coalbed. The results from the volatile matter increase by 11%. The results of the ultimate analysis exhibited an 8% increase for carbon and oxygen after 60 minutes of CO2 flow in the coalbed. On the other hand, there was a reduction of 32% for sulfur. The resultant phenomena occur due to the adsorption capacity of CO2, where the compounds are released from the pores of coal.
Read Article